Red Hat SATELLITE 5.1.0 RELEASE NOTES Manual de instalación Pagina 62
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
44 The Virtualization Cookbook for Red Hat Enterprise Linux 5.2
4.5 Configuring TCP/IP to start at IPL time
Configure the TCPIP service machine to be started when z/VM IPLs. This is commonly
accomplished from the AUTOLOG1 PROFILE EXEC. If the noautolog parameter is
not specified
when z/VM is IPLed, then the AUTOLOG1 virtual machine is started.
Because this virtual machine IPLs CMS, the PROFILE EXEC that is found on its A disk is run.
This is analogous to the /etc/profile file on Linux and the autoexec.bat on DOS systems.
1. Logoff from MAINT.
==> log
2. You should see a new logon window. Logon to AUTOLOG1. Again, the password is the
same as the user ID.
3. At the VM READ prompt, enter the command ACCESS (NOPROF so that the PROFILE EXEC is not
run.
LOGON AUTOLOG1
z/VM Version 5 Release 4.0, Service Level 0801 (64-bit),
built on IBM Virtualization Technology
There is no logmsg data
FILES: NO RDR, NO PRT, NO PUN
LOGON AT 10:06:05 EDT THURSDAY 05/15/08
DMSIND2015W Unable to access the Y-disk. Filemode Y (19E) not accessed
z/VM V5.4.0 2008-05-13 14:27
==> acc (noprof
4. Copy the PROFILE XEDIT from the MAINT 191 disk so XEDIT sessions will have a common
interface among user IDs.
a. Use the VMLINK command to both link to the disk read-only and to access it as the
highest available file mode. The default read password is read:
==> vmlink maint 191
ENTER READ PASSWORD:
==> read
DMSVML2060I MAINT 191 linked as 0120 file mode Z
b. Copy the PROFILE XEDIT to your A disk:
==> copy profile xedit z = = a
5. Make a backup copy of the PROFILE EXEC and edit it:
==> copy profile exec a = execorig =
==> x profile exec
6. You should see the text in the top half of the following example. Modify it as follows.
a. You can safely delete the Address Command line.
b. Add a line to start the TCPIP user ID using the XAUTOLOG command and keep two
statements that start the VSWITCH controllers.
c. Add a line to logoff from AUTOLOG1 when the EXEC is complete. There is no need to
keep that virtual machine running, because its sole purpose is to run the PROFILE EXEC.
Before:
/***************************/
/* Autolog1 Profile Exec */
/***************************/
Address Command
'CP XAUTOLOG VMSERVS'
- The Virtualization Cookbook 1
- Linux 5.2 3
- October 2008 3
- First Edition (October 2008) 4
- Contents 5
- Contents v 7
- Contents vii 9
- Trademarks 12
- The team that wrote this book 13
- Chapters and appendixes 15
- Conventions 17
- Comments welcome 17
- 1.1 What is virtualization 20
- 1.2 This book’s approach 21
- 1.4 Infrastructure design 22
- Planning 25
- 2.1 Bill of materials 26
- 2.2 z/VM conventions 27
- 2.3 Disk planning 28
- DASD versus SCSI/FCP 29
- 3390-3s versus 3390-9s 29
- Disk storage per Linux image 29
- 2.4 Memory planning 30
- 2.5 Password planning 30
- 2.6 Planning worksheets 31
- 2.7 Blank worksheets 34
- 2.7.2 z/VM DASD worksheet 35
- Configuring a desktop machine 37
- Figure 3-2 Setting logging 39
- Saving sessions 41
- 3.2 Setting up a VNC client 42
- 3.3 3270 emulators 43
- 4.1 Installing z/VM from DVD 46
- ==> instplan 50
- Running INSTDVD 52
- Figure 4-8 Load window 53
- ==> cold drain noautolog 54
- ==> no 54
- ==> disc 54
- 4.2 Configuring TCP/IP 56
- not specified 62
- 4.6 Adding paging volumes 65
- Using the CPFORMAT EXEC 67
- 4.6.4 Testing the changes 71
- 4.8.2 Testing the changes 78
- 4.9.1 VM security products 79
- ==> sampnss cms 86
- Servicing z/VM 89
- 5.1 Applying a PTF 90
- 6.4 Enabling the NFS server 106
- 7.2.3 Configuring VDISK swap 128
- 7.2.4 Configuring yum 128
- 7.2.5 Adding additional RPMs 129
- 7.2.10 Configuring SSH keys 134
- 4 6763) is running 135
- 8.2.4 Adding additional RPMs 145
- 8.2.8 Configuring SSH keys 145
- 8.2.9 Rebooting the system 146
- 8.2.10 Verifying the changes 146
- Detach the source disks 151
- Detach the target disks 154
- IPL the target system 154
- 9.3.2 Using the clone script 157
- FLASHCOPY 159
- Installation Server 159
- Master Image 159
- 9.5 Reviewing system status 163
- LNXMAINT 164
- Delete these 167
- Servicing Linux with Red Hat 171
- 12.1.2 Testing Apache 179
- 12.1.3 Turning on a firewall 179
- 12.1.6 Apache resources 182
- Start the LDAP service 184
- Deleting duplicate users 186
- Set a password 189
- 12.3.4 Adding a Samba user 191
- 12.3.6 Testing your changes 192
- 12.3.7 Configuring printing 193
- 12.4.1 Additional resources 194
- Linux kernel development 195
- Web development 195
- Miscellaneous recipes 197
- 13.1 Adding a logical volume 198
- Volume Group - optvg 200
- Creating a physical volume 204
- Extending the volume group 204
- /var/lib/ldap 205
- Configuring LDAP 206
- Configuring automount 207
- 13.4 Rescuing a Linux system 208
- Monitoring z/VM and Linux 211
- INIDICATE LOAD 212
- INDICATE QUEUES EXP 213
- Getting help 214
- Determining who is logged on 214
- Determining storage or memory 215
- Determining software level 215
- 14.2.3 Configuring PERFSVM 218
- Using a Web browser interface 220
- Using a 3270 interface 222
- 14.3 Monitoring Linux 223
- PURGE NSS NAME MONDCSS 228
- CP SAVESEG MONDCSS 228
- References 229
- Quick reference sheets 230
- Prefix commands 231
- :help give help 232
- Appendix B. z/VM source code 233
- The CPFORMAT EXEC 234
- The CHPW540 XEDIT macro 238
- The LABEL540 EXEC 241
- The LABEL540 XEDIT macro 243
- Linux source code 245
- Related publications 257
- Online resources 258
- How to get Redbooks 258
- Help from IBM 258
- Hat Enterprise Linux 5.2 265
Relacionado con productos y manuales para Software Red Hat SATELLITE 5.1.0 RELEASE NOTES
(110 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales